Ventilating And Cooling FAQ From NGMA

NGMA

What is ventilation?

Ventilation is the exchange of air between the inside and outside of the greenhouse. It is used to remove heat from solar radiation, to replenish carbon dioxide and to help control the levels of relative humidity.

What is a ventilation rate?

The ventilation rate refers to the amount of ventilation per unit area. It is measured as cubic feet of air per minute per square foot of greenhouse floor area (CFM per square foot) because the heat load derives from solar radiation and is directly proportional to floor area.

What is the difference between natural and mechanical ventilation?

Natural ventilation results from the wind and stack action from ventilator sashes. Mechanical ventilation is created by electric fans and related equipment.

What does cooling refer to?

Cooling consists of reducing the air temperature by the evaporation of water into the air-stream. The system that does this and moves the cooled air through the greenhouse and exhausts the warmed air is the cooling system.

What is circulation?

Circulation is the movement and mixing of air in a greenhouse to promote uniformity in temperature and humidity and to provide proper air motion throughout the greenhouse.

Why is circulation important to my plants?

Continuous circulation produces a gentle air movement, which maintains a better leaf surface microclimate and prevents pockets of disease-producing high humidity.

Why is ventilation important?

Ventilation allows for the better control of temperature. By allowing an increase in light intensity, which is important to good plant growth, the solar heat can be more effectively removed.

Why should I use exhaust fans?

Exhaust fans are used to provide suffcient airflow through the greenhouse to remove solar heat as fast as it enters. Because the air is warmed gradually as it passes through the house, absorbing heat, the flow rate should be suffcient both to hold the temperature rise to a minimum and to be economically practical.

How do I choose a system?

The selection and arrangement of the ventilating and cooling equipment is determined by the size and type of greenhouse structure and the direction and velocity of the airflow through the house. Allowances also should be made for air density, light intensity and the permissible temperature variation through the house.

How do I get the best results from my system?

For optimum performance, it is necessary to properly size and arrange air inlet openings to produce a uniformly distributed, non-turbulent airflow pattern in the growing area to avoid the mixing of the lower air with the hot air in the upper section of the greenhouse. A definite airflow pattern in a given direction requires an air inlet opening continuous for the entire side or end of the greenhouse. The inlet opening should introduce the air in a horizontal direction at crop level, should not be deflected up or down and should have a low velocity to minimize turbulence and mixing.

Do I need to change my system in the summer?
During the summer, mechanical ventilation alone will usually not maintain the desired greenhouse temperature because the outdoor air is too warm. A way to cool the incoming air should be provided.

What happens to the cooled air as it moves through the house?

As the cooled air moves through the house, it picks up solar heat and increases in temperature by the time it reaches the exhaust fans. This temperature increase is a result of the heat removal process and will vary depending on design. Increasing the airflow or reducing the light intensity can reduce the temperature change. Increased fan capacity can produce increased airflow; shading can reduce light intensity; and good maintenance can minimize the infiltration of air leakage.

Is elevation a factor in creating ventilation and cooling systems?

The air’s capacity to remove heat depends on its weight, not its volume. Because air is less dense at higher altitudes, the elevation of the greenhouse must be considered in design calculations. At higher elevations, a greater volume of air is needed to provide the equivalent weight of air required at elevations that have been established as normal.

How many fans are needed and what do I need to know before having them installed?

The size of fans selected determines the number of fans required. Adequate fans should be used to provide a spacing of not more than 25 feet along the exhaust side of the greenhouse. When possible, the fans should be located on the downwind side of the greenhouse. When three or fewer fans are used in a given installation, one of them should be a two-speed fan to provide for more flexibility of ventilation. Fans should be guarded properly to prevent workers or animals from coming in contact with any moving parts.

For most reliable fan performance, only use fans that have been tested and rated by the Air Movement and Control Association (AMCA) standard test code and that bear the AMCA Certified Rating Seal.

Where should the cooling pad be placed?

The cooling pad should be continuous along the entire side or end of the greenhouse. Pad height is determined by dividing the total pad area by the length. Pads should be confined and secured in a way that provides uniform airflow, prevents sagging, avoids puncturing holes or large openings in them and promotes uniform water flow through the entire length of the pads. The pads should be installed for ease of removal and withstand normal handling and usage. Whenever possible, the air inlet should be constructed in such a way that it can be readily opened and closed without removing the pads.

It is preferable to have the pad assembly located inside the air inlet opening. This will produce less turbulent airflow through the house. For such an arrangement, the air inlet opening need not be continuous but should be at least well distributed.

What if the pad is located outside the air inlet opening?

If the pad is located outside the air inlet opening, it should be continuous, have no large obstructions and should be centered in elevation on the center of the pad so that the airflow is horizontal as it leaves the opening. When the height of the pad exceeds that of the air inlet opening, the pad will extend above and/or below the opening. When this occurs, the pad should be set back from the wall or sash at a distance of at least half the amount of the extension to provide ample room for air to pass uniformly through the entire pad.

If possible the pads should be located on the prevailing wind side of the greenhouse. When the greenhouse is sheltered from prevailing winds by another building or greenhouse located within 25 feet, the location of the pads in relation to prevailing winds is not significant.

How and why should I use baffles?

The cooling air passing through the house will tend to diverge at about a 7-degree-angle or one foot in every eight. Vertical baffles usually are installed particularly with the house, to reduce mixing and keep cool air down at plant level. The baffles should be transparent, spaced approximately 30 feet and held in a fixed vertical plane, and their lower edges should be well above plant level. In greenhouses containing raised benches, a substantial volume of air may travel under the benches to the fan without removing much heat.

A baffle covering two-thirds of the distance from the bench to the ground will force most of the cooling air to crop level for more effective plant cooling.

How do I maintain my water system?

All elements of the water system should be kept well covered to protect it from insects and windborn dirt, which will cause clogging. The water returned to the sump should be screened. The ends of the water distribution pipes should be provided with removable caps or valves to allow easy flushing out for cleaning. Because water is used up in the evaporative cooling process, a supply of makeup water is needed. An automatic float valve should be used for this purpose and also to maintain a proper water level in the sump.

Are winter and summer ventilation systems the same?

Essentially winter and summer ventilation systems are two separate systems having different characteristics and requirements. However, they must tie in with each other to switch from one system to the other during spring and fall. The transition is very important as it determines the inside to outside temperature difference available on a mild, sunny day, and it establishes the airflow design capacity of the winter ventilation system.

Do I need to ventilate differently in the winter?

Mechanical ventilation essentially provides the same benefits regardless of the season, but winter calls for different airflow principals. In the winter, outdoor air is too cold to introduce directly on the plants. The goal of winter ventilation is to introduce the cold air in a turbulent manner. This causes the cold air to mix with the warmer air in the greenhouse, without producing cold drafts at plant level. This mixing is the result of using small high-velocity jets.

In a greenhouse, it is desirable to have many small, well-distributed openings rather than one large one for winter ventilation. It is important that all areas of the greenhouse are at the same temperature. To achieve this, the ventilating system must distribute the air uniformly throughout the house and maintain positive air movement and continuous circulation.

Can I use gravity to circulate the air in my greenhouse?

A powered ventilating system has a real advantage over gravity systems that rely on thermal air currents because it has the energy required to provide uniform air distribution and mixing. Fans that mechanically ventilate greenhouses, combined with perforated transparent plastic tubes, make an ideal system for introducing cold air into a greenhouse in the winter without cold drafts.

What do I use thermostats for in my greenhouse?

Thermostats or controllers are used to turn fans on and off as required to meet changes in outdoor climate conditions and thereby maintain more uniform greenhouse temperatures with lower operation costs.

What do I use a humidistat for?

During warm weather, a humidistat can be used to control the pump of the cooling pad system to help prevent excessive greenhouse humidity. A humidistat that is wired to operate exhaust fans also can help prevent excessive humidity.

Leave a Reply

More From Equipment...

July 30, 2015

Let’s Talk About Starflowers. Why Is Pentas Not More Popular?

It is good to talk about production techniques, performance results and then to see how our friends garden. Diversity of plant material has always been a strength in American garden centers, and we should never run out of plants to get people excited. However, perhaps people are tired of Petunias or Callas or Geraniums, but we will never run out of options to put in front of them. One plant that is often overlooked is Pentas, a fabulous summer crop for late spring sales. These are heat-tolerant plants, and growing them below 65°F in the greenhouse results in significant delay. Fertility should be at least 150ppm nitrogen, but avoid ammonia in the fertilizer. Plants are best grown at a somewhat higher pH than usual, between 6.4 to 6.8. For best presentation, pinch out the center bud. Side flowers will bloom together, and plants will walk off the shelf. Garden centers […]

Read More

July 30, 2015

Spread Your Risk Beyond Spring Sales [Opinion]

Growers who participated in Greenhouse Grower’s 2015 Spring Crops Recap Survey said they have had enough of the uncertainty that the weather brings. They said it’s time to build up sales in other seasons like fall so we’re not so dependent on spring. As a couple of wholesale growers, both from the Southeast, very eloquently stated, our industry has mastered squeezing everything we can out of the spring season. And while this year happened to be a very successful one, thanks to the improving economy and elevated consumer confidence, they said, “now is no time to celebrate.” “Spring is still Christmas in the horticulture industry, but we have done such a good job focusing on spring that we have neglected other seasons,” one grower said. “Having so many eggs in the spring basket is dangerous. Fall will never be what spring is, but having a solid second season is in […]

Read More
Mike McGroarty, owner of Mike’s Backyard Nursery

July 29, 2015

Backyard Success: Mike McGroarty Educates Aspiring Growers

Mike’s Backyard Nursery sits on a long, narrow, 5-acre property located in Perry, Ohio. There, customers can find a variety of flowering shrubs available, all in 2-quart pots, and all for sale for $5.97 each. Owner Mike McGroarty, a lifelong resident of Perry, says the town has a lot of plant nurseries, including 100 wholesale growers within a 10-mile radius of his house. That doesn’t discourage McGroarty, because he knows that while there are a lot of nurseries in his area, no one else is doing what he is doing. McGroarty has learned about plants — and marketing them to his audience — through decades of experience. He has never hesitated to pass along his knowledge to other growers looking to start their own backyard operations, and has created an entire program to educate aspiring growers. McGroarty Likes To Practice What He Preaches McGroarty’s operation serves as the laboratory for […]

Read More
Latest Stories
Heating Feature image

July 27, 2015

In Hot Pursuit Of Heating Trends For The Greenhouse

From biomass boilers to hydronic-heating systems, growers have a range of options to fit their operation’s unique needs. Here’s what five manufacturers had to say about the latest trends.

Read More
lighting feature

June 29, 2015

Customizing Crop Foliage Color With LEDs: Red Leaf Let…

In the first of a four-part series highlighting the multiple uses of light-emitting diodes (LEDs), researchers share how end-of-production supplemental lighting with LEDs enhances red leaf lettuce color prior to harvesting and shipping.

Read More

June 28, 2015

Keep Your Cool In The Greenhouse

Summer is in full swing, and that means growers need to worry about protecting plants and greenhouse employees from brutal temperatures. No sweat! These product manufacturers have offerings to help beat the heat.

Read More
Greenhouse Electrical System

June 23, 2015

Don’t Let Your Greenhouse Electrical System Come …

The size of a greenhouse operation is one of the biggest factors when determining the type of electrical system to install. Part 2 of "Don't Let Your Electrical System Come Up Short" covers locating electrical wires, meeting electrical load demands and environmental considerations.

Read More
Schaefer-fan

June 23, 2015

Schaefer Ventilation Opens Distribution Center In Atlan…

Schaefer Ventilation Equipment, a manufacturer of ventilation and thermal comfort products, has opened a new distribution center in Atlanta, Ga., to increase efficiency and provide faster services to dealers. Additionally, the company has added a new staff member to its agricultural and horticultural division to help expand markets in Latin America.

Read More
HID Lighting System

June 18, 2015

Talking Shop: Using Lighting To Boost Beneficials

Peace Tree Farm was looking for a way to maintain beneficial insect populations through the winter. It found a potential solution through the use of rotating HID lighting.

Read More

June 17, 2015

Costa Farms Reduces Greenhouse Emissions With Solar Pow…

Costa Farms is seeking to make sustainability a top priority at its headquarters and two other buildings in Miami with the recent construction of new solar panels, which will replace 25 percent of the company's power usage with solar energy.

Read More
aquatrols

June 3, 2015

Aquatrols Renews Cooperative Research And Development A…

Aquatrols Corporation recently announced a new Cooperative Research and Development Agreement (CRADA) with Dr. Matt Madsen and the USDA Agricultural Research Service. The objective of the new CRADA is to further refine and evaluate surfactant seed coating technologies for use in wildfire rehabilitation, turf and pasture grasses, restoration species and other horticultural and agricultural systems. The three-year agreement renews a CRADA that Aquatrols first signed with the ARS in 2012. The original partnership has resulted in promising field and greenhouse trials, pending patents and initial steps toward commercialization of the surfactant seed coating technology. “We are very encouraged by the work that Dr. Madsen and his team have put together over the past three years,” says Aquatrols’ President and CEO Tracy Jarman. “This innovative technology has shown incredible potential with wide-ranging impacts in multiple industries. Aquatrols’ stated mission is to change the way the world grows and this technology has the […]

Read More
Growers are looking for low-cost options for temperature control, like circulating fans and exhaust fans.

April 10, 2015

New Ways To Give Growers Control Of The Greenhouse Envi…

From heating systems to circulation fans, manufacturing companies are finding new ways to help growers control the greenhouse environment, save on energy costs and streamline production.

Read More
Polyarch Berns

March 12, 2015

The Energy Efficient Greenhouse

New coverings technology means today’s films, plastics, shade cloths and climate screens slash heating and cooling costs while improving crop productivity year round. We checked with manufacturers to see what’s new and uncovered some best practices for buttoning up your greenhouse. Here’s what you need to know about the latest trends.

Read More
FormFlex_MTZ Hanging Basket

March 11, 2015

4 New Ways To Automate Your Operation

These new automation products can help streamline labor-intensive tasks, saving time and labor and increasing productivity.

Read More
Outfitting Your Greenhouse

February 24, 2015

Save Energy With The Right Greenhouse Glazing

The glazing you choose can make a big difference in your energy bill and the uniformity of your crops.

Read More
Michigan State University Extension

February 24, 2015

Ethylene From Defective Greenhouse Heaters Damages Crop…

Malfunctioning greenhouse heaters can lead to crop damage from ethylene and carbon monoxide induced illness for workers. Michigan State University's Extension educators Tom Dudek and Randy Beaudry teach you how to recognize the symptoms and check greenhouse heaters to avoid the concern.

Read More
Havest Automation Robot

February 18, 2015

Robots Grab Hold Of Growers’ Material Handling Needs

Harvest Automation’s HV-100 robots automate one of the hardest, most labor-intensive jobs at growing operations – plant spacing. With more technology coming, investing in robots could become even more realistic for growers of all sizes.

Read More

February 1, 2015

4 Lighting Products For Your Operation

These new lighting products have been developed for maximum energy efficiency in greenhouse production. Check out the slideshow to see which products are right for your operation.

Read More
LumiGrow

January 30, 2015

LumiGrow Expands Customer Base In 2014

LumiGrow, Inc. is adding more than 125 new commercial, governmental and research customers to its roster of customers, and beyond the new accounts added this year, many existing customers significantly increased the number of LumiGrow products they use and research customers made LumiGrow a part of their efforts to add to the body of knowledge about spectral science.

Read More
harvest automation featured image

January 13, 2015

Harvest Automation Extends Robot Rental Program

Harvest Automation's robot rental program proved to be such a success for the company that it is being extended through the spring. The program was unveiled last year as a way for customers to get started with HV-100 robots.

Read More

January 9, 2015

Innovations In Irrigation

Need help improving your irrigation? Check out these new products.

Read More